FS: 1" lathe indexable turning and parting tools plus dinner inserts

[mattthemuppet]

Next up, turning tools

Used $20ea, 3 for $50. All have good clamps and shims
Free cat
Parting/ grooving tools and a push knurler

Iscar tang grip 1-1/4" blade TGFH 32-3. One end in good condition, the other looks ok $10
Accutrak knurling holder with one ground down knurl $10

Three beat up parting/ grooving tools $10 for all three

 

[mattthemuppet]

Two Carballoy 1-1/4" parting tool holders for 1" tool blocks $20 each

 

[mattthemuppet]

New 1" tools, $40ea, 3 for $100

Sandvik SCLCL 16 4D

Sandvik SSDCN 16 3D

Sandvik DTJNL16 3D

Kennametal NER164D NI5

Two Horizon Carbide TSR164D, these look like they take top notch inserts, but I don't have any 4xx size ones to try

 

[mattthemuppet]

CNMG5xx, 4xx and CNMA432
CNMG5XX, look new but have random chips in them $5 the lot

Sumitomo CNMA432 CBN insert, looks new $10

Top Notch NB3R inserts, used but usable I think. 10 for $5. I've got LOTS of these

Used but usable CNMG4XX, each has at least one useable tip, some have more. Not sure about the CBN though. $10 the lot

Four new Sandvik CNMG432MM $10

 

[mattthemuppet]

9 new Mitsubishi VNMG332LK and four used but usable inserts $20

 

[mattthemuppet]

DNMG DNGP and DNMM CBN

Two new DNGP431 $5


Used but usable $5

Two DNMM CBN inserts, left 432 and right 431 $10 each

Three new Sumitomo DNMG431 inserts $5

 

[mattthemuppet]

Oddballs

Widia CSR100093 insert, used but hard to tell $10

New Allied C6484:X2 LHFG inserts, $5

 

[1 Jaw Chuck (Chuck Evans)]

Next up, turning tools

Used $20ea, 3 for $50. All have good clamps and shimsView attachment 410470View attachment 410471View attachment 410472View attachment 410473
Free catView attachment 410474
Parting/ grooving tools and a push knurler
View attachment 410475
Iscar tang grip 1-1/4" blade TGFH 32-3. One end in good condition, the other looks ok $10
Accutrak knurling holder with one ground down knurl $10
View attachment 410476
Three beat up parting/ grooving tools $10 for all three
View attachment 410477

Pm sent

 

[BugRobotics]

I'll take all the CBN inserts.

 

[rawen2]

I'll take the:
"9 new Mitsubishi VNMG332LK and four used but usable inserts $20" if not already spoken for. Sending PM.

 

[Donkey Hotey]

More pictures of cat? Will she fit in a large flat rate box? Is she already sleeping in a flat rate box?

 

[Halcohead]

I'll take the following:
1. kennametal DDJNR 16 3 holder
2. one set of Top Notch NB3R inserts, used but usable I think. 10 for $5
3. Two new DNGP431 $5
4. Three new Sumitomo DNMG431 inserts $5

And that cute little calico cat.

PM incoming

 

[4GSR]

If you have any more of the top notch inserts, I'll take 10 for $5.
Ken

 

[plastikdreams]

Ok where's the dinner??

 

[mattthemuppet]

More pictures of cat? Will she fit in a large flat rate box? Is she already sleeping in a flat rate box?

Ask and you shall receive. She probably would fit in a large flat rate box, but until you open it you won't know if you'll live or die from the result

 

[mattthemuppet]

If you have any more of the top notch inserts, I'll take 10 for $5.
Ken

I have LOADS of these

Ok where's the dinner??

The cat is not for eating. Besides there's not much to her under all the fluff

 

[Donkey Hotey]

Ask and you shall receive. She probably would fit in a large flat rate box, but until you open it you won't know if you'll live or die from the result

Probably die. Those carbide-tipped cutters look ominous.

 

[1 Jaw Chuck (Chuck Evans)]

Matt,

Everything arrived today, well packaged!

Thanks!

Chuck

 

[mattthemuppet]

awesome, thanks Chuck!

 

[mattthemuppet]

All the new tool holders are still available, anyone want to bite at $30 each?

Used
Last down threading
Vnmg left and right
Snmg
Knurling
Parting blade and holder

Random inserts